Embedded Systems and Power Electronics

Total Pageviews

About Me

My photo
I am currently a PhD student at UC Berkeley, following a 6-year journey working at Apple after my undergrad years at Cornell University. I grew up in Dhaka, Bangladesh where my interest in electronics was cultivated, resulting in the creation of this blog.

BTemplates.com

Powered by Blogger.

Jun 18, 2011

Interfacing a DS18S20 with an AVR


This can be a complete project on its own - a simple DIY digital thermometer with LCD display and only a handful of parts - ATMEGA88, DS18S20 and only a resistor running off a regulated 5v supply.

Display type - LCD (can be 16x1, 16x2 or anything larger)
Controller: ATMEGA88
Programming Language: BASIC
Compiler: mikroBASIC PRO for AVR

'''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
program Temp_DS1820

'Microcontroller: ATmega88 (Atmel AVR)
'Programming Language: BASIC
'Compiler: mikroBASIC PRO for AVR v2.10
'Sensor: DS18S20
'Programmer: Syed Tahmid Mahbub

dim LCD_RS as sbit at PORTB2_bit
dim LCD_EN as sbit at PORTB3_bit
dim LCD_D4 as sbit at PORTB4_bit
dim LCD_D5 as sbit at PORTB5_bit
dim LCD_D6 as sbit at PORTB6_bit
dim LCD_D7 as sbit at PORTB7_bit

dim LCD_RS_Direction as sbit at DDB2_bit
dim LCD_EN_Direction as sbit at DDB3_bit
dim LCD_D4_Direction as sbit at DDB4_bit
dim LCD_D5_Direction as sbit at DDB5_bit
dim LCD_D6_Direction as sbit at DDB6_bit
dim LCD_D7_Direction as sbit at DDB7_bit


sub procedure ConversionDelay()
    delay_ms(800)
end sub

sub procedure StabilizeDelay()
    delay_ms(200)
end sub

dim Temperature as word
dim TempH as byte
dim TempL as byte
dim TLow as byte
dim vDisp as string[9]
dim DecimalPoint as byte

main:
     DDRC = $FE 'RC0 input for One-Wire
     LCD_Init()
     LCD_Cmd(_LCD_CURSOR_OFF) 'LCD Cursor off
     LCD_Cmd(_LCD_CLEAR) 'Clear LCD
     StabilizeDelay() 'Wait for sensor and LCD to stabilize
     vDisp = "+124.5 'C"
     LCD_Out(1, 1, "Temp:")
     while true
         OW_Reset(PORTC, 0) 'Reset command to initialize One-Wire
         OW_Write(PORTC, 0, $CC) 'Skip ROM Command
         OW_Write(PORTC, 0, $44) 'Convert_T command
         ConversionDelay() 'Provide delay for conversion
         OW_Reset(PORTC, 0) 'Reset command to initialize One-Wire
         OW_Write(PORTC, 0, $CC) 'Skip ROM Command
         OW_Write(PORTC, 0, $BE) 'Read Scratchpad Command
         Temperature = OW_Read(PORTC, 0) 'Read Temperature low byte
         Temperature = Temperature + ((OW_Read(PORTC, 0)) << 8) 'Read Temperature high byte and convert low and high bytes to one 16-bit word
         TempH = Hi(Temperature) 'High 8 bits of Temperature
         TempL = Lo(Temperature) 'Low 8 bits of Temperature
         DecimalPoint = Temperature.B0 'Check if Temperature is integer or fractional
         if (Temperature and $8000) then 'If reading is negative
            vDisp[0] = "-"
            TempL = byte((not TempL + 1) >> 1)
         else 'If reading is positive
            vDisp[0] = "+"
            TempL = TempL >> 1 'Shift one position right (divide by 2) to get integer reading and get rid of decimal point
         end if
         vDisp[1] = TempL div 100 + 48 'Get hundreds and convert to ASCII
         vDisp[2] = (TempL div 10) mod 10 + 48 'Get tens and convert to ASCII
         vDisp[3] = TempL mod 10 + 48 'Get units and convert to ASCII
         if (DecimalPoint) then 'If reading is fractional, ie has 0.5 at end
            vDisp[5] = "5"
         else 'If reading is a whole number
            vDisp[5] = "0"
         end if
         LCD_Out(1, 8, vDisp) 'Show temperature
     wend
end.


Hex file + Schematic + Code freely available for download:
http://www.4shared.com/file/WMXzmmO5/DS1820_Temp_LCD.html

The code can be freely used and there is no copyright restrictions or anything as such. Only credit the author (me) where necessary. 

5 comments:

  1. Hi Tahmind
    thanks for the very useful info on avr timer use. Can you help with controlling a single stepper motor with ATMega128 and a gekodrive?
    I am having trouble getting it to run fast. I am using C but am quite new to avr. I need to run the stepper forward for a set number of steps (length) only. Many thanks.
    Richard (South Africa)

    ReplyDelete
  2. Which compiler are you using? Can I see the code you've done so far?

    ReplyDelete
  3. @Tahmid: Which schematic capture program are you using? I'm using Eagle 5.11.0 on Ubuntu 11.10.

    ReplyDelete
  4. I'm currently using Proteus in Windows.

    ReplyDelete
  5. http://www.4shared.com/file/WMXzmmO5/DS1820_Temp_LCD.html
    This link is not active.
    Can you share active link pleases.
    Best Regards
    Karanbir

    ReplyDelete